Cypress Semiconductor CY8C24894 Spezifikationen Seite 33

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 50
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 32
CY8C24894
Document Number: 001-53754 Rev. *F Page 33 of 50
AC Programming Specifications
Tab le 26 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C T
A
85 °C, or 3.0 V to 3.6 V and –40 °C T
A
85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 25. 3.3-V AC Analog Output Buffer Specifications
Symbol Description Min Typ Max Units Notes
t
ROB
Rising settling time to 0.1%, 1 V step, 100 pF load
Power = low
Power = high
3.8
3.8
s
s
t
SOB
Falling settling time to 0.1%, 1 V step, 100 pF load
Power = low
Power = high
2.6
2.6
s
s
SR
ROB
Rising slew rate (20% to 80%), 1 V step, 100 pF load
Power = low
Power = high
0.5
0.5
V/s
V/s
SR
FOB
Falling slew rate (80% to 20%), 1 V step, 100 pF load
Power = low
Power = high
0.5
0.5
V/s
V/s
BW
OBSS
Small signal bandwidth, 20 mV
pp
, 3 dB BW, 100 pF load
Power = low
Power = high
0.7
0.7
MHz
MHz
BW
OBLS
Large signal bandwidth, 1 V
pp
, 3 dB BW, 100 pF load
Power = low
Power = high
200
200
kHz
kHz
Table 26. AC Programming Specifications
Symbol Description Min Typ Max Units Notes
t
RSCLK
Rise time of SCLK 1 20 ns
t
FSCLK
Fall time of SCLK 1 20 ns
t
SSCLK
Data setup time to falling edge of SCLK 40 ns
t
HSCLK
Data hold time from falling edge of SCLK 40 ns
F
SCLK
Frequency of SCLK 0 8 MHz
t
ERASEB
Flash erase time (block) 10 40
[19]
ms
t
WRITE
Flash block write time 40 160
[19]
ms
t
DSCLK
Data out delay from falling edge of SCLK 45 ns V
DD
3.6 V
t
DSCLK3
Data out delay from falling edge of SCLK 50 ns 3.0 V V
DD
3.6 V
t
PRGH
Total flash block program time (t
ERASEB
+ t
WRITE
), hot 100
[19]
ms T
J
0 °C
t
PRGC
Total flash block program time (t
ERASEB
+ t
WRITE
), cold 200
[19]
ms T
J
0 °C
Note
19. For the full temperature range, the user must employ a temperature sensor user module (FlashTemp) or other temperature sensor, and feed the result to the temperature
argument before writing. Refer to the Flash APIs Application Note AN2015 for more information.
Seitenansicht 32
1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 49 50

Kommentare zu diesen Handbüchern

Keine Kommentare